Відео

Good day. What temperature should the oil applied to the brake caliper pins be resistant to? Can lithium soap based grease be used? I would appreciate it if you could help me with the caliper pins.

Good day. What temperature should the oil applied to the brake caliper pins be resistant to? Can lithium soap based grease be used? I would appreciate it if you could help me with the caliper pins.

Tanx man 👌

seems like all the grease would be trapped in the rubber boot

thank you for sharing your insight, visual reference and alternate solutions for depressing this style of caliper piston. i’m immensely grateful.

Legend! Simple and easy instructions which I couldn't find elsewhere. Was a nightmare for me trying to pop it back through the hole though haha. Thanks, mate!

Hi, thankyou for the video. A question for you, but exist a second sensor? Or it is only one? Thanks

Thanks

Thank you, thank you, thank you. Didn’t find this video until after I had purchased a gear puller to remove the arm. Couldn’t get it to center, and remove the arm. Back to YT to find your video. One minute later, RESULTS! Sending back the puller today. Many thanks for the quick, cheap, effective tip!

Which one is better for my Polo 2006 1.4 petrol?

Technically its one ground .... its not like there are 2 different channels or 3 channels or even 4 channels for spark to travel thru, its all the same piece of metal

That was a great lesson, thank you!

Time to redo my rear slides. Put grease on the tip.

10/10 video.

I've always disliked multiple ground strap plugs. You can't create multiple sparks at one time. They simply wanna sell you some they're gonna convince you that you need. I went to try the e3 plugs one time. And right away noticed they're non adjustable as far as gap goes. I needed a .035 gap for my C/20. I ran em and noticed at high rpm I'd have an odd misfire feel. I took em out, and used a dremel to cut 2 of the 3 ground straps off. With that outta the way I measured the gap. .045! Huge gap, no wonder the misfire. With the remaining ground strap I adjusted it down to .035. And they ran very well after that mod. Lotta money for plugs I gotta fix myself in my opinion. Standard plugs are the best you'll get out there.

👍🙂 good job.

Great tip cheers from Atlantic Canada👍🏼😎🇨🇦

Go to 2010 Mini Cooper S work perfectly thank you

Loaned my tool out for the job and wasn't sure what to do. The screwdriver trick worked perfectly

Something new to be learned, thanks man!👍

Not quite sure why you didn't just add 0.1 of water and retest? But this video is genuinely interesting and a valuable test. Thanks.

Prepare your prybar 😄 when remove the rear seat plastic, it may not easy as you see

I used a G clamp.

Hello, what's they size off the seal? Thanks You

Grease is Grease; unless you prefer hog lard....just select a lubricant that's NOT going to rot away the rubber grease caps that the caliper bolt runs through. Grease your slide pins WITH the grease caps attached at top of bolt and THEN reassemble......

I remember years ago falling for this BS and bought a set of Split Fire plugs for my 1969 6pk Super Bee. Oh did they run terrible. Waste of money and I think they're still on a shelf in my garage. Good quality single electrode plugs with the proper heat range is the only way I go

What if it is too strong and literally sprays the roof instead of windscreen?

Thank you ! Excellent tutorial, very well filmed 👍

Thanks for this .. I found your video after I had done this myself and all went well. However although the car runs ok she now always takes a good few cranks to start (as if the fuel runs back from the injectors each stop) where as before she started instantly. Did I miss something do you think?

May this fix work on a peugeot partner year 2006 aswell ?

I've found the best plug is the bosch twin electrode plug... just like aviation plugs. Easily 100,000 miles. GMC 350 V-8.

Very helpful vedio..thank u..❤

I used 4 electrodes Bosch in a k11 Nissan Micra 1.0 16V. It worked out perfectly but there was no increase in the performance either. It was the same as with the single electrode ones.

Thank u very much. I changed my battery seeing your video

In my 2001 doge ram 2500 iridium plug was worst seems missing on plugs, after change to E-3 spark plugs seems No more missing on cyl and better starts and operation of vehicle

Why do these kits all have clockwise & anti-clockwise drivers, when the rear brakes screw in clockwise?

My k12 has a bc above the radio. Different methode of working?

Perfect thank you👍

thank you for this information

It has been so helpful thanks

Can green antifreeze be poured instead of this pink antifreeze?

Спасибо тебе! Привет из России🤝

Question My door has a big dent and my plan is to remove the cover on the inside of the door, ass showed in the video, and push the dent out. But my window cant get all the way down. It stops around 30% left of its way, because of the dent. Can I do it with the window up? And coud i damge my window when i push the dent out?

How to get rid of old grease and dirt stuck inside? Without full overhauling

Hello tnx for your videos ..my ashtray cover don't close ..how to fix this problem plz

👍🫡

Question I have - I bought this kit and it works great but, how do you clean the tube afterwards? The one way valve and neoprene connector sorta keep the fluid trapped in there

My cube doesn’t fit my Mazda calipers, I’ve struggled with the pliers. Last time I just “sent it” and used a c clamp for pressure and rotated the body with channel locks. Sub optimal but got it done. Should have gone and borrowed the tool, but just sharing as it works in a pinch.

is it normal thats its clickking ????

Worst car ever, rot sets in form leaving French Built ones, red ones loose lacqure, 2 door ones a ones where most people end up in AnE for,